So I been thinking of this for awhile been doing research on cheap homemade crane jibs when use correctly and a little tought put into it it takes filming to a professional level and you can make them for under 100bucks!!<br />
<br />
After doing some homework I've come to the conclusion that a 12 foot jib is the easiest smoothest shoot... Opinions????<br />
<br />
<br />
As far as Dolly's go some as above applies <br />
<br />
Best one I've seen so far is two rails on a 4inch piece of plywood <br />
Camera mounts to another piece of plywood with notched out rollerblade wheels (skateboard looking if you will) <br />
The notches ride the 2rails and you lift one side slowly to roll the camera down the plywood for like going around corners and what not...<br />
<br />
Take your filming / editing to the next level!!!

I had the tank off today while I was wiring in my second radiator fan, moving my ignition to the air box, and doing the kleen air mod. So I asked myself what the hell why not just dent it now?<br />
<br />
I scoured the internet for as many pictures of good ones as I could find and printed them out. There weren't many so I decided if mine turned out OK I would post some good pictures of it... I also heard lots of people complain about how lousy the 05 06 tanks were for denting so I was a little concerned.<br />
<br />
<br />
I made sure to support the bottom of the tank well with bags of lead shot (sand bags would work, too). I didn't want to put any dents on the bottom or screw up any of the tabs!<br />
<br />
<img src="http://stuntride.com/vbstunt/attachment.php?attachmentid=15501&amp;d=1340953558" border="0" alt="" /><br />
<br />
Like the stunt bums video, I threw a rag over the cap, and put an aluminum dist over that. Instead of a cinder block, I used a big hammer to whack the disk. It worked really well and I think it gave much more control than a cinder block would have. I made sure to keep it even, and if one side was going in more than another it was easy to correct.<br />
<br />
After a few good whacks with the mallet...<br />
<br />
<img src="http://stuntride.com/vbstunt/attachment.php?attachmentid=15502&amp;d=1340953589" border="0" alt="" /><br />
<br />
This is the inside clearance once it was all smashed down. I don't think I would want to go any farther. As it is, it will probably be a pain to fill.<br />
<br />
<img src="http://stuntride.com/vbstunt/attachment.php?attachmentid=15503&amp;d=1340953589" border="0" alt="" /><br />
<br />
Here it is all dented up and lightly sanded ready for filler. It hardly even needs any filler though, just a few light passes!<br />
<br />
<img src="http://stuntride.com/vbstunt/attachment.php?attachmentid=15504&amp;d=1340953654" border="0" alt="" /><br />
<br />
<img src="http://stuntride.com/vbstunt/attachment.php?attachmentid=15505&amp;stc=1&amp;d=1340954147" border="0" alt="" /><br />
<br />
I've never been more happy to not have an ass before! I can really see how this tank wouldn't allow enough dent for some people, but for me it's prefect! I did a few test fits to my posterior and it is super comfy, I even rocked it way back pretty much vertical and was able to stay in it without any grip enhancers. Tomorrow I'll putty it up and hit it with some thick primer until I decide what color to paint it.

<b><font size="5"><font color="Sienna"><font face="Century Gothic">Badass Industries Steel Frames</font></font></font><br />
</b><br />
<br />
<b><font face="Arial Black"><font size="3">Get the best prices and best Steel frames out there!!! <br />
</font></font></b><br />
<br />
<b><font face="Arial Black"><font size="3">-$750 for half. $1450 for full. <br />
</font></font></b><br />
<br />
<b><font face="Arial Black"><font size="3">-Quality TIG welds, quality DOM steel. (CAN be fixed with mig If needed, NO heat treating nessecary to keep strength)<br />
</font></font></b><br />
<br />
<b><font face="Arial Black"><font size="3">-Machined neck. (only one on the market) (cuts weight)</font></font><br />
</b><br />
<br />
<b><font face="Arial Black"><font size="3">-frames are usually super close to stock +/- 1-3 lbs.</font></font></b><br />
<br />
<b><font face="Arial Black"><font size="3">Tell him Scary Jerry sent you to get this deal. <br />
</font></font></b><br />
<br />
<b><font face="Arial Black"><font size="3">1(701)330-6772 <img src="images/legacy/smilies/cheers.gif" border="0" alt="" title="Cheers" class="inlineimg" /></font></font></b><br />
<br />
<br />
<img src="http://i251.photobucket.com/albums/gg285/meforu/framebuild2.jpg" border="0" alt="" /><br />
<img src="http://i251.photobucket.com/albums/gg285/meforu/framebuild3.jpg" border="0" alt="" /><br />
<img src="http://i251.photobucket.com/albums/gg285/meforu/backframe.jpg" border="0" alt="" />

<a href="http://gizmodo.com/5921995/jvcs-tiny-hd-action-camera-looks-like-a-freaking-tank" target="_blank">http://gizmodo.com/5921995/jvcs-tiny...-freaking-tank</a><br />
<br />
looks promising.<img src="images/legacy/smilies/shruggs.gif" border="0" alt="" title="Shruggs" class="inlineimg" />

So many awesome build threads and projects on here. Would you guys like to see a specific section for this?<br />
<br />
I'll close polls in 2 weeks...

Ive been shopping around for a good case and want to know what has and had not been worth the money for people. Anyone know anything about this one? <br />
<br />
<a href="http://item.mobileweb.ebay.com/viewitem?itemId=120780030993&amp;index=1&amp;nav=SEARCH&amp;nid=68296578837" target="_blank">http://item.mobileweb.ebay.com/viewi...id=68296578837</a>

Looking for a setup street legal stunt bike, clean title.<br />
<br />
I'm from Ontario so don't post up if you're in cali or az or something. I will come down this weekend

So my buddy is talking about putting his radiator fans on the outside of the radiator..<br />
<br />
Kinda makes sense you push air into rad when you ride anyways <br />
<br />
I got a rad cage and I could easily weld mount tabs to it if this works for a 2nd fan<br />
<br />
Sorry if this is a repost search button dosnt work on my phone<br />
Anyone that has done this a little input would really help out<br />
<br />
Thanks I heart you guys !!!! <img src="images/legacy/smilies/cheers.gif" border="0" alt="" title="Cheers" class="inlineimg" />

Just noticed that it doesnt show, idk if its my computer er something. am i the only one<img src="images/legacy/smilies/shruggs.gif" border="0" alt="" title="Shruggs" class="inlineimg" />?

<img src="http://a5.sphotos.ak.fbcdn.net/hphotos-ak-ash4/246472_377448812317938_1040242614_n.jpg" border="0" alt="" /><br />
<img src="http://a3.sphotos.ak.fbcdn.net/hphotos-ak-ash4/401941_377440075652145_1635605033_n.jpg" border="0" alt="" /><br />
<img src="http://a6.sphotos.ak.fbcdn.net/hphotos-ak-snc7/397797_287792604616893_962098331_n.jpg" border="0" alt="" />